Uncle carpenter’s know-how: How to make and care for camphor wood cutting board & chopping board.

Uncle carpenter’s know-how: How to make and care for camphor wood cutting board & chopping board.


Uncle carpenter
The know-how that Uncle Carpenter made Camphor cutting & chopping board. Hi
It’s an Uncle carpenter.
Today, I will show you how to make a board made with a holiday gift just as I had noticed before.
I introduced the first sheet of furniture from the foundation to how to manage it at home.
The next video will show you how to make an armchair with pine wood.
Before watching the video, please subscribe and like and press the alarm. Finally made camphor wood cutting board.
The beautiful grain and smooth surface are so beautiful. The first step is to cut the well-dried (Moisture content 8~12%)camphor plank to the desired size. I tried to make it small, but I made it with a big cutting board for a gift. The size of the cutting board was 420 * 250 * 25T 2EA and 450 * 300 * 28T 1EA. I used to make electric planes, but now I use automatic planes. It is really easy. It was well polished. The bond now used is Titebond 3, a bond used for attaching and filling the wood used for food ingredients such as cutting boards. Generally
When filling a small hole, it mixes wood powder and bond, but when the hole is not big enough, put the bond first like this, and put the wood flour on it with sandpaper. Add a little bit of wood flour on top of it until it is clean. Do you see any holes filled in like this?
The fault was removed. This time we make the length 450 width 300 thickness 28T cutting board. Before using the automatic planer, if the concave side goes down and there is a shake by pressing the wood on a flat surface, the plane must first be flattened, and then a balanced cutting board is made later. Sanding is first sandpaper # 80, then sanded three times to # 200 # 400. Thereafter, water sanding and oil sanding are added. I also made a cutting board stand.
Do you know the difference in quality between when it is and when it is not? Use a band saw to make a groove in the place where the cutting board will be inserted. Next, use a belt sander to make a smooth curve. Use a trimmer to chamfer make for high-quality cutting board. Drill using a drilling machine. Finish the cutting board holder with trimmer and assemble. Now we are making wooden sticks to fill the holes. If you put the wooden stick and put the bond, than cutting board holder is completed. After the bond is completely hardened, put it in water for about 3 hours to make the surface rough. After 3 hours, sand the surface with # 120 sandpaper while the tree is wet. Do you see falling water?:) Sanding until the water is dry and the surface is smooth. This way, it does not get rough even when washed in water like now. Dip once more in water and repeat twice more with # 400 sandpaper. Finally, finish using # 400 sandpaper by hand. If you do this carefully, it will be very smooth. The sandpaper process using water only takes two days. So this video has a lot of workload. When this process is over, it is completely dry and sanding again. It is finally time to do oil coating. First apply lots of Howard Butcher block oil on the cutting board. This oil is harmless to human body. Howard Butcher block oil penetrates the surface of the cutting board and forms an oil film on the inside. Normally, it absorbs oil by immersing it in an oil container, but since I do not make only a cutting board Oil well enough to allow this to flow down sprinkle, then let it absorb for at least 10 hours. Nearly last, I rub it with a # 400 sandpaper on a board that has absorbed enough oil. If you look closely, you can see something like a grease spot. This is not a grease spot, but the lint on the surface of the wood. When all this lint disappears, it gets a smooth, water-resistant surface. Use a tissue paper to wipe all the surface oil and dry it again. This time, the surface is coated with Watco butcher block oil.Howard butcher block oil has good permeability and Watco butcher block oil has good coating ability. Because Watco butcher block oil is a hardening oil, it is used in a small container little by little. Use the syringe to put it in a small container. My baby have a cold ache these days. All people watch this video please be careful of cold ache. Because Watco butcher block oil is a hardening oil, it can leave marks if applied too thickly. In my case, apply oil and wipe off with cotton after 2 ~ 3 hours. Repeat this process two or three times. Laser engraving is done using each popular. I originally had to do the oil work before, but I forgot. Finally, the coating is made using wax for the cutting board. At this time, you can use conditioning oil. Leave the butcher block conditioning oil in the house and apply it to the cutting board once every six months. Then you can use the cutting board for a long time. I worked with a hand grinder for convenience. However, you can also work with your hands. It looks like the cutting board shines brightly.:) Finally finished. It takes a lot of care to make a cutting board. It is so beautiful. Maybe people receive gifts are happy, too? The following videos are inexpensive, but I’ll show you how to make an armchair that requires a lot of time and effort.
If the video is interesting, subscribe and like and press alarm. And I look forward to the next video.


46 thoughts on “Uncle carpenter’s know-how: How to make and care for camphor wood cutting board & chopping board.

  1. 울집에도 구멍 뚫린 도마 있는데ᆢ
    우와 진짜 정성이 많이 가네요
    결이 예뻐요
    잘 만드셨어요
    수고하셨습니다
    감기 조심하시고
    편안한밤 되세요 👍🍀💕

  2. 와.. 선물 받으시는 분은 정말 좋으시겠어요 .. 시간과 정성 이 정말 대단하십니다🥰🥰👍👍👍

  3. 와 목공 영상을 이렇게 보는건 처음인데 남자로써 굉장히 멋져보입니다!!
    자주 올게용 함ㅋ게 소통해욯~~규우됵 쿡!

  4. 어릴때는 이런거 만드는거 참 잼나했는데.. 물론.. 이런 고퀄 말고요 ㅋㅋ 이렇게 대리만족하게 해주셔서 땡큐네요. 그런 마음에 꾹꾹 눌르고 가요 ^^앞으로 자주 놀러올께, 아참 가장 중요한 광고도 다 봤어요 ㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋㅋ

  5. 와.. 정말 너무 탐나는 도마에요~! 선물받으시는 분들 모두 행복하실것 같아요!

  6. 이제 설명도 나오네요^^ 점점 영상에 퀄리티와 완성도가 99.9%가 되네요^^ 올해도 복 많이 받으세요~

  7. 역시 캄포도마!! 무뉘가 수려하군요 선물 받으신분은 행복하시겠슴다 캄포가 자체 향균력도 있어 도마목으로는 적극 추천요. 물사포 기름사포 하나하나 잘 배워 갑니다 쓰앵님~~^^

  8. 와 정말 정성이 대단하시네요..도마를 물에 세시간 불리고 말려도 변형이 오지는 않나요??

    이번에 월넛 도마 만드려고 하는데 월넛도 같은 방법으로 작업해도 괜찮을까요?

  9. 정말 탐나는 작품입니다. 제작자의 정성과 장인정신이 느껴지는 영상입니다. 거기다 친절한 설명까지 훌륭하십니다.

  10. 다른 채널에서도 도마 만드는거 봤는데 물사포까지 하면서 이렇게 꼼꼼하게 하시는분 첨봐요

  11. 만드시는걸 보니까 감히 얼마냐고 묻기가 송구하지만… 그래도 하나쯤 소장하고픈 물품이네요. 가격이 얼마입니까?

  12. 친구들 선물로해도 너무 좋을듯해요..
    도마로 쓰기엔 예뻐서 아까울듯요….
    탐나는 도마~^^

  13. 저도 만들어 보고 싶은 열망을 불러 일으키시는 군요~
    그런데 캄포나무는 어디서 구할 수 있을까요~

  14. 아재 목수님 안녕하세요. 좋은 영상 잘 보고 있습니다. 다름이 아니오라 어버이날을 맞이하여 어머니와 가족들에게
    선물을 하고자 아재 목수님 영상보고 도마재료를 사서 사포질 하고 물샌딩 부분에서 물에 담구었다가 다시 말리는 과정에서
    나무에 금이가고 목재가 휘어 버리는 불상사가 생겼습니다. 아재 목수님 전 아주 초보라 처음해보는 것이라
    많은 실수가 있었을 것이라 생각되어 물샌딩 물에 불려 반복하시니 반들반들한 것에 욕심이 앞서 ㅋ
    저에게 일어나는 일이 없이 물 샌딩할 때 아재님 처럼 이쁘게 만들 수 있는 방법은 없는지요?
    몇 번의 영상을 보고 따라한 초보의 간절함 입니다. 좋은 가르침 주시면 감사드리겠습니다. 늘 건강하시고 행복하세요

  15. 매번 볼때마다 경이로움을 감출수가 없습니다. 저 도마 얼마를 드려야 살수 있는 도마일까요

  16. 꼼꼼한 설명과 훌륭한 솜씨. 전문가다운 영상이네요 . 집에서 만들어볼까 했다가 포기하고 갑니다~^^

  17. 도마 만들기 본편 외에도 잘 보고 배웠습니다.
    1차 오일은 흡수용
    2차 오일은 코팅용으로 두 제품을 꼭 같이 쓰야 하는지요? 1차 왁스 또는 2차오일 왁스 만으로 사용 해도 될런지요?
    1차 와 2차 같이 쓰면 별로라고 그래서 문의 해 봅니다

  18. 만드는 과정이 클래스로 있었으면 좋겠어요.

    파시면 바로 사겠네요.

    좋은 영상 감사합니다

  19. 저희 아버지가 이거 만든다고 캄포나무 3판을 샀어요….정말이지 저는 관심 없는데 같이가서 하는게 정말이지 다 불태워버리고 싶을 정도로 싫었습니다.

  20. 1차 하워드 침투오일 바르고, 얼마 정도 있다가 2차 브처블락 도막오일을 바르면 될까요??
    1차 오일을 바르면 계속해서 마르지 않는 상태로 남아있을것 같습니다.

  21. 여자지만 목공예술 배우고싶다 실생활에도 사용하고 직접 만들면 겁나 뿌듯하고 좋을듯 너무 멋있는거 같음

Leave a Reply

Your email address will not be published. Required fields are marked *